Practical advice from a local plumberS R Francis • Bromley & surrounding areas
SR Francis flame and water drop logoS R FrancisPLUMBING & HEATINGmaintaining the flow of H₂O
Which? Trusted TraderTrustATrader
← All Homeowner Hints
Homeowner Hint #7

Why Does My Boiler Pressure Keep Dropping?

Big leaks are easy to find. It’s the small ones that are more tricky.

The first thing I ask anyone who tells me their boiler pressure keeps dropping is: how often are you topping it up?

Every few monthsA very small drop over a long period is usually something to monitor, not panic about.
Every weekThat is regular enough to suggest a leak or another fault that needs investigating.
Every day or twoThere is a definite problem. The pressure is going somewhere and the cause needs to be found.

A Small Drop Is Not Always a Big Problem

Needing to top the pressure up once after radiators have been bled or work has been carried out is very different from doing it every morning. Even over a few months, a small pressure loss does not automatically mean there is a serious leak.

Think of a balloon that is half full of water and half full of air. If you let the air out, you have lost the pressure, but you have not lost any water. Losing pressure does not always mean water has leaked out.

A sealed heating system can behave in a similar way. Air trapped in the system can work its way to radiator vents or automatic air vents and be released. When that air leaves, the gauge can fall without the same amount of water having leaked away. That is also why bleeding a radiator can leave the boiler showing low pressure.

See Homeowner Hint #5: How to repressurise your heating system →

First, Have a Good Nose Around

Before assuming the leak is buried under a floor, look for the simple things. Check:

  • Radiator valves and pipe connections
  • The airing cupboard
  • Underneath the boiler and visible pipework
  • Ceilings below upstairs radiators
  • Rust, green or white crusty deposits
  • Damp smells or patches
Do not dismiss a crusty radiator valve because it has “been like that for ages”. Deposits, staining or rust around a joint usually mean water has been escaping. A tiny weep can stay small for months and then get worse. If the fitting is wet, it is leaking.

Check the Small Copper Pipe Outside

The pressure-relief discharge pipe should be a small copper pipe outside, normally turned back towards the wall or terminating safely low to the ground. It is left visible because water coming from it is a useful sign that the boiler’s pressure-relief valve has opened.

It is not the white plastic overflow pipe you might see coming from a loft tank or the rear of a toilet. It is also different from the boiler’s condensate pipework, which on a correctly installed boiler should run to a suitable drain or purpose-made condensate soakaway. The pressure-relief pipe does not need to terminate in a drain.

A useful check: if you can safely reach the correct copper pipe, loosely fix an open clear sandwich bag beneath the outlet, using an elastic band only to keep it in place, and check it after a day or two. It can catch a small drip that would otherwise disappear. Never cap, seal or obstruct the pipe, be aware that discharged water may be hot, and remove the bag after checking. If you are unsure which pipe it is, leave it alone and ask.

Why the Pressure Can Rise, Drip and Then Fall

Water expands as it heats. The expansion vessel inside the boiler or heating system is there to absorb that extra volume and stop the pressure rising too far.

What Is an Expansion Vessel?

Think of it like a metal pot with an air-filled rubber balloon inside. As the heating water gets hot and expands, it pushes into the vessel and squeezes the balloon. As the water cools and contracts, the balloon expands again and pushes back. It is constantly taking up the expansion and then releasing it.

If the vessel loses its air charge or the rubber diaphragm fails, that cushion disappears. The expanding water then has nowhere to go, so the pressure climbs too high when the heating comes on.

The Cycle

1Heating comes on
2Failed vessel cannot absorb the expansion
3Pressure rises and the relief valve dumps water outside
4Boiler cools and the gauge falls too low
5Homeowner tops it up and starts the cycle again

The pressure-relief valve is doing its job: protecting the system from excess pressure. It may drip or discharge water outside while the heating is on. When the boiler cools, the gauge falls too low, the homeowner tops it up again, the heating comes back on and the whole cycle starts again.

Do not try to make it last longer by topping it up higher. After a week or two of doing this every day, people often start filling the system to 2 bar or even 2.2 or 2.3 bar, hoping it will still have pressure in the morning. It will not solve the fault.

A domestic boiler’s safety valve is normally set to open at around 3 bar. Starting at 2.2 or 2.3 bar leaves only about 0.7 or 0.8 bar before the valve opens. With a flat or failed expansion vessel, there is no proper cushion to absorb the expansion, so topping it up higher simply makes the valve open sooner and discharge more water. It does not make the pressure last longer.

It may take only a relatively small amount of water to move the gauge from normal pressure to zero. The heating circuit can still contain water; it simply no longer has enough pressure to operate properly.

If It Is Not the Expansion Vessel, Where Else Can It Go?

A leak on an upstairs pipe or radiator will normally show itself eventually as a damp patch or mark on the ceiling below. Ground-floor pipework can be harder to trace, especially when it runs beneath floorboards or is buried in concrete.

There can also be a hidden leak inside the boiler. On some boilers, water escaping from a heat exchanger can make its way into the condensate route, so there is no puddle underneath the appliance.

This is where proper diagnosis matters. An engineer can test whether the pressure loss is inside the boiler or somewhere on the heating circuit. Thermal imaging can sometimes reveal an unexpected warm spread beneath a floor, and a radiator that repeatedly fills with air can provide another clue to the affected area.

Do not remove the boiler casing or try to isolate internal boiler components yourself. Those checks belong with an appropriately qualified heating engineer.

Should I Keep Topping It Up?

We live in the real world. If the boiler pressure has dropped and you need a shower or the house is freezing cold, you are going to top it up so the boiler works.

Temporarily topping up the system may therefore be unavoidable. But understand what it is doing: you are keeping the system running; you are not repairing the problem.

Think of a bucket with a hole in it. You can fill it whenever you need to, but the water is still escaping. Unless you find and repair the hole, you cannot expect the bucket to remain full.

If you repressurise after bleeding a radiator and the pressure then holds, keep an eye on it. If you are topping it up every day or every week, the pressure is going somewhere and the cause needs to be found.

If the pressure drops straight back down, there is an active leak, or the gauge quickly climbs towards the red when the heating runs, stop repeatedly topping it up and call an engineer.

Boiler Pressure Problems in Bromley?

Call or WhatsApp Steve

If your boiler pressure keeps dropping, get in touch and I’ll talk you through the basic checks. A few useful answers can often narrow the problem down before I arrive:

  • How often are you topping it up?
  • Does it drop overnight or after the heating has been on?
  • How long has it been happening?
  • Have you noticed damp patches, ceiling marks, crusty valves or an outside drip?

If it needs a proper investigation, we can arrange a visit and get to the bottom of it.

For help with other plumbing and heating faults, see our Bromley plumbing services.

SR Francis Plumbing and HeatingBusiness operating address (no walk-in premises): 19 Holmcroft Way, Bromley BR2 8ADCall 07794 814961 · WhatsApp Steve